ad

news

hc:
Aliexpress WW Vevor Many GEOs Лабиринт OnePlus [CPS] Many Geos Fernsnpetals [CPS] IN Komily WW IGP [CPS] WW
lc:
Fairyseason WW DHgate WW Banggood WW Economybookings Many GEO's Lenovo Many GEOs Mego.travel Norton [CPS] WW ChicMe WW
ua:
EvroGroshi [CPS, API] UA Kreditmarket [CPS, API] UA Slon Credit [CPS,API] UA Microcash [CPS] UA
FanDuel Fantasy Sports Register + Join a Group
Booking.com

Wednesday, February 2, 2022

Making methods of students' handicrafts

Making methods of students' handicrafts Answer; How to make handicrafts? All kinds of melon seed shells can be used for Collage; Eat the remaining jelly shells and string them together to make wind chimes; Used disposable paper cups and beverage bottles can be cut into flower baskets and so on. All kinds of bottles and cans can be made. For example: 1. Use a toilet paper tube as the body, and stick the ears, eyes, nose and mouth of a small animal on it, which is a lovely small animal. Toilet paper can also be used to make tree trunks. 2. Envelopes can be made into pocket puppets. Draw or paste the eyes, nose, mouth and ears, and cut a hole (semicircle) on both sides of the envelope. The child or teacher can put his hand in, and the thumb and little finger extend out from the small holes on both sides to make a puppet. There are many more, you can use your imagination. All kinds of bottles and cans can be made. It's a pity to throw away the discarded cans made of yogurt bottles. This article teaches you how to use cans to make exquisite metal paintings. It's a popular handicraft. 1、 Raw materials and production tools: all kinds of cans, pens, rulers, carbon paper, image rubber pads about 3cm thick; Small, medium and large scissors and carving knives, color pen, watercolor or oil painting pigment, latex, multi-functional glue, sandpaper, backing paper, backing cloth, mirror frame, etc. 2、 Making method: 1. Rubbing base map: first design a beautiful picture as the base map, and then rub the base map on the front of the can piece with carbon paper (the can has been cut from the middle before, and the head and tail are not used). Because the long side is hard, the picture should be rubbed on the middle of the can piece as much as possible. 2. Tracing and engraving: put the expanded can piece on the rubber pad and trace and engrave the drawing with a ball pen according to the copied lines. The tracing force should be moderate, and it is better to recognize the line imprint on the metal. 3. Molding: extrude and scribe the engraved base map. According to the requirements of the base map, for the parts that need to be raised, place the metal sheet on the rubber pad with the reverse side facing upward, and squeeze and scribe the picture with a pen and pen tip according to the line imprint. For the concave part, squeeze and scribe the front figure of the metal sheet with the above method. The operation force shall be moderate and uniform, so that there shall be no obvious extrusion and scratch marks on the metal surface. Excessive force will break the metal surface. If it is too light, the three-dimensional effect of the picture cannot be achieved. Through repeated extrusion and engraving and front and back trimming, the picture can produce three-dimensional effect. 4. Cleaning: after molding, wash the picture with detergent to remove stains and make the picture clean. 5. Cut and color the picture with scissors, and trim the picture that can't be carved. Then, according to the requirements of the manuscript, the cut graphics are spliced together with glue to form a complete picture. Then, color with pigment as needed. It's best to use the natural color of the can. 6. Framing: check and repair the picture in an overall and all-round way to make the picture more perfect. Then, paste the lining paper (lining cloth) on the bottom plate of the frame with glue, and then paste the painting glue on the lining paper (lining cloth) and install it into the frame.

No comments:

Post a Comment

Tool kits given to 64 artisans - Tribune India

Under the Mukhyamantri Swavalamban Yojna (MSY), the Kangra district Industries Centre organized a one-day workshop for handicraft artisans a...